TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > Technical Forums > Buick Turbo Tech
Register FAQ Community Calendar Today's Posts Search

Buick Turbo Tech General technical support for the 86-87 Buick turbo cars

Reply
 
Thread Tools Display Modes
  #1  
Old 02-19-2009, 12:24 PM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default Cotton's Line Lock Installation

1. remove line from master cylinder, closest line to the firewall.


2. Take supplied brake line and attach short side to the master cylinder

3. the other end goes into the brass straight fitting on the inlet side of the line lock solenoid. You may then attach the line lock where it sits on the fenderwell

4. carefully bend the original brake line to the outlet side of the line lock and attach, you can now bleed the line at that location. I usually have someone help bleed at this point.

5. now we can hook up our switch, attach one wire to ground, run the other wire to your switch and supply 12 volt power to the other side of your switch. You are done.. test it out and have fun..
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #2  
Old 02-20-2009, 01:16 AM
WSLN 6 WSLN 6 is offline
Member
 
Join Date: Aug 2008
Location: Saskatoon, Canada
Posts: 46
Default

Good writeup Jack! That's exactly how I installed mine years ago......until the NHRA techs said to move it to the "proper" location after the proportioning valve on the frame.....just a heads up!
__________________
1986 T-Type
Leather/column
What turbo?
Powerstroke IC, Forged Stroker,GN 1's,Razor alky, XFI, 3.5" DP, Extrm stg2 tranny,TA Headers
PTC 9.5 N/L 3400 stall
Reply With Quote
  #3  
Old 02-21-2009, 10:44 PM
Brad's Avatar
Brad Brad is offline
BEACHBUM RACING
 
Join Date: Dec 2007
Posts: 4
Default

Thanks Jack. I'll be ordering one shortly.
Reply With Quote
  #4  
Old 03-02-2009, 02:14 PM
BadAssGN BadAssGN is offline
addicted to Boost
 
Join Date: Apr 2008
Location: Near Toronto Canada
Posts: 5
Default

Jack

I find that the Brake light comes on when I hook them up this way. the sensor in the proportioning valve senses pressure on the front and none on the rear.

have you noticed this in the past?

The last on I did, I removes both lines coming out of the Prop valve, plugged one hole and installed a tee after the line lock.

No more brake light when using the linelock.

Just a thought....


Quote:
Originally Posted by JCotton1 View Post
1. remove line from master cylinder

2. Take supplied brake line and attach short side to the master cylinder

3. the other end goes into the brass straight fitting on the inlet side of the line lock solenoid. You may then attach the line lock where it sits on the fenderwell

4. carefully bend the original brake line to the outlet side of the line lock and attach, you can now bleed the line at that location. I usually have someone help bleed at this point.

5. now we can hook up our switch, attach one wire to ground, run the other wire to your switch and supply 12 volt power to the other side of your switch. You are done.. test it out and have fun..
__________________
1987 GN
235ci, forged pistons,steel caps, race ported irons
PT70 Ptrim 72 lb injectors, extender extreme
ARP everything, 4" intake. ported throttlebody,
Mease plenum, EGR delete race ported and welded
intake. port matched to felpro 1200s , Cotton Front mount,
F body rad, TA girdle on the Diff, Atr bar, Boxed control arms,
Stock headers and THDP, ultra high flow cat (gutted)
Hooker exhaust
Reply With Quote
  #5  
Old 03-02-2009, 04:15 PM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

Quote:
Originally Posted by BadAssGN View Post
Jack

I find that the Brake light comes on when I hook them up this way. the sensor in the proportioning valve senses pressure on the front and none on the rear.

have you noticed this in the past?

The last on I did, I removes both lines coming out of the Prop valve, plugged one hole and installed a tee after the line lock.

No more brake light when using the linelock.

Just a thought....
Yes, I have, it only requires a lite tap of the brake pedal and it centers in the valve. I don't mind as it works like a warning lite that the line lock is or was applied. A lite tap and the lite goes out. As for the NHRA rule, I've heard that for 10 years, have never seen it in writing nor have I ever been called on it... (been to a few NHRA tracks) so for what it's worth, I'm just trying to keep it simple... thanks for the reminder though...
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #6  
Old 03-02-2009, 06:12 PM
waGoN's Avatar
waGoN waGoN is offline
Long Roofs are sexy!
 
Join Date: Nov 2007
Location: Messachusetts
Posts: 394
Default

It is much more complicated putting it after the proprotioning valve.
The PV is what splits the one line into two for the the two front wheels.
In order to use the line lock, you have to block one of the ports, run the other to the line lock, then connect both front brake lines to it, and you have to find a good place to put it. There isn't one, unless you want to run new lines to the brakes. If you want to try to use the ones that are there, then your only option is to mount it almost on top of the prop. valve. You can't do that, because it will be in the way of the shifter linkage.

Oh, and the light will go on no matter where you have it. But like Jack said, a tap of the pedal and it goes out.

Edit: BA, I just noticed that you had luck installing it after the prop valve and not getting the light on. Mine was installed that way, and I always got the light.
__________________
Brian

Keep it shiny side up, but show them your dirty side once in a while.

11.3@123mph on 195/75/14" whitewalls. Yes, 195s!
11.2 on the big giant slicks. What's the point? Maybe I'll go back to the whitewalls. They are lighter and have less rolling resistance.

Last edited by waGoN; 03-02-2009 at 06:47 PM.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 05:39 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.