TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > Technical Forums > Electronic Tuning

Electronic Tuning Chips, scan tools, aftermarket engine management

Reply
 
Thread Tools Display Modes
  #1  
Old 07-29-2008, 10:43 PM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default Long story short

My XFI aux ports are not functioning properly. These [aux 1-4 ports] are suppose to switch to ground when the set parameters are met ( ie. rpm/tps% ect), but as soon as the engine is running, they are grounded---All the time----they don't wait for my parameters to be met. Any ideas? Bad XFI box?
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #2  
Old 07-30-2008, 10:31 AM
TurboBabe's Avatar
TurboBabe TurboBabe is offline
The Boss
 
Join Date: Nov 2007
Location: With Jack
Posts: 1,362
Default

Quote:
Originally Posted by BrianHynes View Post
My XFI aux ports are not functioning properly. These [aux 1-4 ports] are suppose to switch to ground when the set parameters are met ( ie. rpm/tps% ect), but as soon as the engine is running, they are grounded---All the time----they don't wait for my parameters to be met. Any ideas? Bad XFI box?

I'm on it... I doubt it's a box problem, more likely a wiring issue. Did you check with John yesterday.. I'll be on the horn this morning..
__________________
Lorrie
www.cottonsperformance.com
Reply With Quote
  #3  
Old 07-31-2008, 01:25 AM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

Jack, I wasn't able to get ahold of Dave at FAST today. Maybe you could try him in the morning (hopefully he won't be that busy). Like you said, it might be in the way John wired the adapter harness. Thanks brother!
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #4  
Old 07-31-2008, 01:26 AM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

By the way, the pins I'm using are B1 and B2. These are labeled Aux 1 and Aux 2 respectively.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #5  
Old 08-01-2008, 11:22 AM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

For anyone who has been following this thread, I spoke with Dave @ FAST. We both feel the box might have an issue, but I am going to try some things first. As required by the "Power Adder" function, I will run a switched +12v to the XFI pin B19. Even though XFI instructions don't mention this for the aux ports, maybe this will allow the aux ports to function properly (fingers crossed). I have also been in touch with a friend of Jacks in Kentucky (thanks for your help Jack), and will be talking again with Steve this morning. Steve is taking the time to diagram what he did for his set up, and will update me. I'm hoping all goes well, so I can get the NOS dialed up.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #6  
Old 08-01-2008, 07:49 PM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

Well everything is now working through the "Power Adder" function. My aux ports are still not working, but I'll wait 'till the season is over to send the box back to FAST for repair.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #7  
Old 08-04-2008, 01:20 AM
trbochrgd1's Avatar
trbochrgd1 trbochrgd1 is offline
I can't drive 55!
 
Join Date: Nov 2007
Location: North Jersey
Posts: 518
Default

Quote:
Originally Posted by BrianHynes View Post
Well everything is now working through the "Power Adder" function. My aux ports are still not working, but I'll wait 'till the season is over to send the box back to FAST for repair.
Ok, so did you test it out yet? Or do you need the aux ports to make it work?
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar.

New best 9.44 @ 143!
Reply With Quote
  #8  
Old 08-04-2008, 10:03 AM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

Quote:
Originally Posted by trbochrgd1 View Post
Ok, so did you test it out yet? Or do you need the aux ports to make it work?
I don't need the aux ports Michael. Everything functions through the "Power adder" function now. I still want to get the aux ports functional, as they give you alot of options ie. operating a shift light, ect..

The car Hasn't been out in 2 weeks . It just won't stop raining. We did have 1 nice day last week, but I had work and a soccer game. You and Jack will be the first to know when I test it.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 05:22 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.