TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > Technical Forums > Buick Turbo Tech
Register FAQ Community Calendar Today's Posts Search

Buick Turbo Tech General technical support for the 86-87 Buick turbo cars

Reply
 
Thread Tools Display Modes
  #1  
Old 02-18-2008, 05:41 AM
Lou Lou is offline
Junior Member
 
Join Date: Feb 2008
Posts: 3
Default No power to fuel pump

I am not getting main power to fuel pump.
Reply With Quote
  #2  
Old 02-18-2008, 10:41 AM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

Quote:
Originally Posted by Lou View Post
I am not getting main power to fuel pump.
ok, If you installed a new hot wire kit, check the inline fuse. You can unplug it at the tank and rehook up the stock plugs, make sure it still runs...
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #3  
Old 02-18-2008, 06:37 PM
Lou Lou is offline
Junior Member
 
Join Date: Feb 2008
Posts: 3
Default No power continued...

Actually the new hot wire kit is ok. The original harness is not powering up hot wire kit, no power to the pump from original wiring harness.
Reply With Quote
  #4  
Old 03-09-2008, 12:04 AM
Recklessrob's Avatar
Recklessrob Recklessrob is offline
Junior Member
 
Join Date: Dec 2007
Posts: 4
Default

Check your (factory) fuel pump relay and fuse.
__________________
Rob
--------------------
87 GN BGN00367D
87 Mazda B3800P/U*deceased
84 Pontiac GP 4.1 litre
96 Chevy S-10 (new project)
Independent Amsoil Dealer

ihadav8.com
Turbo Buicks.net
Reply With Quote
  #5  
Old 03-15-2008, 04:22 AM
Sam Colalillo's Avatar
Sam Colalillo Sam Colalillo is offline
Member
 
Join Date: Feb 2008
Posts: 47
Default

Lou,
I'll try to help, Going off memory here so bare with me.

First thing to check is your fuel inj. Fuse, is it OK?

The connector that goes into the fuel tank sending unit contains three wires. Black is ground. A tan wire with a white tracer is the power wire going directly to the fuel pump do you have power at this location? Remember unless your car is running you are only going to have power for two seconds after the key is turned to the run position. This is because the ECM only allows the pump to run for two seconds when the ignition is turned to the run position. The third wire is a power wire also; it is the one that is connected to the rheostat in your tank, it tells your gauge what fuel level to read depending on how much voltage it is receiving.

You have a fuel pump test lead wire on your Buick, you can supply power to this wire and the fuel pump will run if it is not bad. This wire is located behind the A.C. compressor next to the valve cover right above the header (I think it is a grey wire). Next to it will be the Tachometer test lead. (Sometimes people plug these two leads together accidentally and their tachometers go bonkers). By supplying 12 volts to this lead the pump should run, if it dont the pump may be bad.

If it does then continue on.

Next check fuel pump relay wires. The fuel pump relay is the middle relay on the passenger side fender. One of the wires connected to this relay is a dark green wire with a white tracer, located in pin A1 of the fuel pump relay wire harness socket assembly. When you turn the key to the run position the ECM triggers 12 volts for two seconds to the Dark green wire with a white tracer. In order to check this wire for power you will need some help. Get your test light on this lead and have your assistant turn the key to the run position, it should turn on the test light for two seconds, does it?

If the test light indicates you have power for two seconds then the internal Ecm relay is working. If it does not light then there is a problem with this circuit.

If it lights then turn the ignition key to off and probe the tan with white tracer wire plugged into the fuel pump relay (socket B).

Did it light up for two seconds?

If it did not light up check the black with white tracer, is it making a good ground?

If the ground is good and the tan with white tracer is not powering up you probably have a bad relay.

Also remember the oil pressure switch CANNOT cause your pump not to run (unless the pump relay is bad). It's there as a back up for the relay, and hooked in parallel. If the relay goes bad, the oil pressure switch bypasses it as long as you have 4lbs of oil pressure the fuel pump will stay running.

Hope this makes sense.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:53 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.