TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > The Racing Forums > ET's and MPH

ET's and MPH Post up your track experiences. ET and MPH, what's your combo...

Reply
 
Thread Tools Display Modes
  #1  
Old 01-10-2008, 01:21 AM
scot w.'s Avatar
scot w. scot w. is offline
28lbs on pump gas! :)
 
Join Date: Jan 2008
Location: Smokey Mtns, in TN
Posts: 34
Default My 2007 best time..

6.76 @ 103.9 in the 1/8th on pump gas & Methanol
__________________
1986 GN, 235cu. Bal & blueprinted 109 block, PT-70 gtq, Billit mains on 2&3, ARP main studs, J&E pistons/dry film coated w/ ceramic tops, Dry-Film coated bearings(rods,main,cam), M&A stage III alum heads-race ported-wire locked w/ARP studs, ATR headers, Hyd. flat tappet 221/218-525lift/cam, crower 1.65 roller rockers, race ported intake, 70mm Acufab TB, percision plenum,3"THDP, 85lb inj flow matched, P.T.E S/L IC, Razors ALKY kit, 9" 3800 N-stall N/L art-carr conv, Moser axles, H&R bar

Last edited by scot w.; 01-11-2008 at 12:14 AM.
Reply With Quote
  #2  
Old 01-10-2008, 10:36 AM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

That's a good start, no doubt, by the looks of that motor on the stand, there is more where that came from....
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #3  
Old 01-10-2008, 08:10 PM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

What motor?, What stand?, What am I missing here?
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #4  
Old 01-10-2008, 08:20 PM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

Found 'em!
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #5  
Old 01-10-2008, 08:38 PM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

Quote:
Originally Posted by BrianHynes View Post
Found 'em!
Good boy... I knew you were sharp....
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #6  
Old 01-10-2008, 11:50 PM
scot w.'s Avatar
scot w. scot w. is offline
28lbs on pump gas! :)
 
Join Date: Jan 2008
Location: Smokey Mtns, in TN
Posts: 34
Default

Quote:
Originally Posted by BrianHynes View Post
What motor?, What stand?, What am I missing here?
I fixed it for ya Brian!
Attached Images
File Type: jpg New Engine pic.jpg (80.4 KB, 19 views)
File Type: jpg New Engine pic #2.jpg (88.0 KB, 17 views)
__________________
1986 GN, 235cu. Bal & blueprinted 109 block, PT-70 gtq, Billit mains on 2&3, ARP main studs, J&E pistons/dry film coated w/ ceramic tops, Dry-Film coated bearings(rods,main,cam), M&A stage III alum heads-race ported-wire locked w/ARP studs, ATR headers, Hyd. flat tappet 221/218-525lift/cam, crower 1.65 roller rockers, race ported intake, 70mm Acufab TB, percision plenum,3"THDP, 85lb inj flow matched, P.T.E S/L IC, Razors ALKY kit, 9" 3800 N-stall N/L art-carr conv, Moser axles, H&R bar

Last edited by scot w.; 01-11-2008 at 12:16 AM.
Reply With Quote
  #7  
Old 01-11-2008, 12:13 AM
BrianHynes's Avatar
BrianHynes BrianHynes is offline
Nitro boy
 
Join Date: Dec 2007
Location: Northern New York
Posts: 732
Default

Thanks!

Jack, can you shorten the minimum amount of letters required to post. Sometime, I would just like to say "Thanks"
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
Reply With Quote
  #8  
Old 01-11-2008, 01:13 AM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

Quote:
Originally Posted by BrianHynes View Post
Thanks!

Jack, can you shorten the minimum amount of letters required to post. Sometime, I would just like to say "Thanks"

I'll try... been looking how to figure out the pics in a sig.... haven't figured it out yet..

Scot, you can post pics.... give the signature a break, I'm trying to figure it out. You look a little winey there...
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #9  
Old 01-11-2008, 01:57 AM
scot w.'s Avatar
scot w. scot w. is offline
28lbs on pump gas! :)
 
Join Date: Jan 2008
Location: Smokey Mtns, in TN
Posts: 34
Default

Quote:
Originally Posted by JCotton1 View Post
Scot, you can post pics.... give the signature a break, I'm trying to figure it out. You look a little winey there...
Yes sir Mr. Cotton, Is that better MR. Cotton? Thanks man..
__________________
1986 GN, 235cu. Bal & blueprinted 109 block, PT-70 gtq, Billit mains on 2&3, ARP main studs, J&E pistons/dry film coated w/ ceramic tops, Dry-Film coated bearings(rods,main,cam), M&A stage III alum heads-race ported-wire locked w/ARP studs, ATR headers, Hyd. flat tappet 221/218-525lift/cam, crower 1.65 roller rockers, race ported intake, 70mm Acufab TB, percision plenum,3"THDP, 85lb inj flow matched, P.T.E S/L IC, Razors ALKY kit, 9" 3800 N-stall N/L art-carr conv, Moser axles, H&R bar
Reply With Quote
  #10  
Old 01-11-2008, 01:59 AM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

Quote:
Originally Posted by scot w. View Post
Yes sir Mr. Cotton, Is that better MR. Cotton? Thanks man..
Now dats what I'm talkin about!!!
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:10 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.