#1
|
||||
|
||||
M/T drag radials
Where is the best source for these. I'm thinking 275-60-15 rear with skinnies up front. Thanks
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
#2
|
||||
|
||||
I have always gotten my slicks/drag radials from Jegs. Always had good luck with them....Well at least for that, cam shaft kits for turbo buicks are another story.
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143! |
#3
|
||||
|
||||
Honestly, I did not check Jegs. I looked @ Summit, and didn't see them. I'll have to look tomorrow.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
#4
|
||||
|
||||
MT et street radials are on a nationwide backorder, have been since last october
except for a few of the less popular sizes youll have to do a lot of searching and maybe trade in some favors to get ahold of a set of 275/60s that someone might have stashed away and dont expect them to be cheap , last i heard was 500 a set on the few 28s left check this thread http://www.turbobuick.com/forums/bra...ack-order.html
__________________
Paul... NJ rep MAGNABUICK.com the 86 3450lbs ...1.44 6.19@112 9.72@138 , 109 234cu stock mains and bolts , irons, the 87 ttop ,1.37 6.0@ 114 9.45 @ 141.9 25 psi !! 109 235cu .gn1 alum, certified roll cage . the 87gnx'd FAST B2B TA49 ..back to all stock original #s 109 and trans hipro w stagerite the 87 GN ttop ..all stock with vac brakes 86 WH1 mini tubbed roll caged 109, extreme 2004r all on pump 93 and alkycontrol |
#5
|
||||
|
||||
Quote:
I found this out quickly. Fortunately, M/T is not the only "Drag radial". I have been looking at the Hoosiers and M&H's. I really like the looks and dimensions of the Hoosiers. Wish there was some feedback on these.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
#6
|
||||
|
||||
Well, I ordered Hoosier DOT drag radials today. I had to verify that they did indeed have a DOT stamping, 'cause thay look too close to a slick. Good thing my car gets limited use and no wet roads.
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
#7
|
||||
|
||||
Found out today, that M/T is recertifying all their DOT drag radials. It appears that there is no realistic release date in site. Maybe they are waiting to release their winter "Snow radials".
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
#8
|
||||
|
||||
you scared me. I need new MT 325 DRs for Spring. Summit has em next day ship. I don't know about those Hoosiers, the warning on hoosiers site about public road use would make me go MT since they are actually meant for street driving when needed. I never saw a pic of the hoosier though.
|
#9
|
|||
|
|||
I'd like to put the 295-50-16 on my kirbans but it looks like I willl be waiting.
|
#10
|
||||
|
||||
Quote:
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! |
Bookmarks |
|
|