|
|
#1
10-13-2009, 02:09 PM
|
||||
|
||||
As always.....
You were right Jack!
 Damn your good! I'll give you a call later....  I guess I need that and a 160 degree thermostat.
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143! 
|
|
#2
10-14-2009, 09:38 AM
|
||||
|
||||
|
Quote:
How you been Michael? Hows the car running after the head gasket swap?
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
|
|
#3
10-18-2009, 03:48 PM
|
||||
|
||||
|
Yes, it was the turboflange gasket. I ran a Wednesday a couple of weeks ago and it ran pretty good the first pass, 9.62 @140.11 60' 1.37,22 psi . I was in such a rush that morning that I unfortunelty forgot the laptop... So I only had one shot at recording a run. I got back to the pits checked everything over, called Jack, and then checked the plugs. Everything looked pretty good. I went up for another pass and It left very soft, with no boost, the top of first gear it was like a rocket booster kicked in and it took off! I don't have the timeslips in front of me but it was a low 10 second run at 137 mph. So I got back to the pits, it was pitch black out at this point and I was by myself. I check everything over the best I could and I found the vacuum port on the fuel pressure regulator that was loose. I tightened that and thought that was it. Went up again and it was just as bad as the second pass. So I put it back in the trailer and didn't touch it till Sunday. I started it up Sunday in the trailer and noticed a loud noise from the turbo area. As you can see the gasket was blown out! Thank goodness, because I thought my converter was fried... I'm just waiting for the gasket right now and a new thermostat (it was running a little hot).
Hopefully we get a chance to go out one more time this year.
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143!
|
|
#4
10-22-2009, 01:04 PM
|
||||
|
||||
|
Any luck with that flange gasket?
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143!
|
 |
| Bookmarks |
|
|
Linear Mode
