TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > The Racing Forums > ET's and MPH
Register FAQ Community Calendar Today's Posts Search

ET's and MPH Post up your track experiences. ET and MPH, what's your combo...

Reply
 
Thread Tools Display Modes
  #1  
Old 01-17-2008, 06:38 PM
PaceCarTA's Avatar
PaceCarTA PaceCarTA is offline
Da Big Cheese
 
Join Date: Dec 2007
Location: central NJ
Posts: 50
Default 10s (now 9 seconds !! ) on 93 and meth

86 GN hardtop , all necessary safety equipment

1.431 4.204 6.576 102.80 8.647 10.418 126.99

93 and methanol
275/60-15 MT drag radials
through the mufflers

engine management :
stock ECM modded for injectors
turbotweak chip ,25/24 timing

shortblock:
main caps-stock
rods-stock
pistons -stock
crank-stock
bolts -stock
no girdle!

heads-ported stock irons
12pt ARP studs


LT gt71Q .85 a/r exh .70 a/r compresor 4"in 2.5" out
PTE turbosaver
royal purple 5-30,10-40

cam/valvetrain
212/208 flat tappet hydraulic
rockers- stock
shafts-stock
pushrods-stock
valve covers-stock

intake-stock (no porting)
plenum-mease sheetmetal 70mm
TB- Accufab 70mm

injectors MSD 75#
fuel rail-stock
fuel lines -stock
accufab regulator
ATR dbbl pump -340s
red VB

dequick V2 FMIC
alkycontrol dual nozzle
translator+ LT1(blowthrough in uppipe)
KN 4"in x 12", 4" mafless pipe

stock headers (no port)
ATR external 3" DP / hks 40mm gate
MSBC-1 12G elec boost controller
2 3/4 SS dual exhaust w/ magnaflows

trans- 200-4R BRF , stageright brake
PTS deep pan
converter AC 9" NL 3600

rear:
stock 8.5 housing
moser 33spline
moser elims
moser spool
3.42 gears

driveshaft-HD custom 3" moly ,spicer yokes

suspension :
Front-eibach -1" springs, no frt swaybar
rear- hrparts HD swaybar ,stock boxed lowers, stock uppers , stock bushings, stock springs
shocks are std low buck replacements -no trick ratios

other stuff
champion billet a/c delete bracket
gbody heater only air box complete conversion
vac brake conversion
B&m linelock
B&m trans cooler
Fbody rad
dual fans hotwired
token CF hood
token frt and rr stock appearing bumpers
PI GNX 8gauge VDO cockpit cluster w/knock
XD-16


race weight 3450

has since gone 104.9 1/8 , 129.8 1/4 , turbotweak wideband 6.0 ,LC-1
__________________
Paul... NJ rep MAGNABUICK.com
the 86 3450lbs ...1.44 6.19@112 9.72@138 ,
109 234cu stock mains and bolts , irons,
the 87 ttop ,1.37 6.0@ 114 9.45 @ 141.9 25 psi !!
109 235cu .gn1 alum, certified roll cage .
the 87gnx'd FAST B2B TA49 ..back to all stock original #s 109 and trans hipro w stagerite
the 87 GN ttop ..all stock with vac brakes
86 WH1 mini tubbed roll caged 109, extreme 2004r
all on pump 93 and alkycontrol

Last edited by PaceCarTA; 12-15-2012 at 02:01 AM.
Reply With Quote
  #2  
Old 01-17-2008, 07:49 PM
trbochrgd1's Avatar
trbochrgd1 trbochrgd1 is offline
I can't drive 55!
 
Join Date: Nov 2007
Location: North Jersey
Posts: 518
Default

WOW! That is extremely impressive! Looks like you got that thing really dialed in. Good Job!
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar.

New best 9.44 @ 143!
Reply With Quote
  #3  
Old 01-18-2008, 02:14 AM
Phoneguy Phoneguy is offline
Brother Jack is my Pastor
 
Join Date: Nov 2007
Location: O'fallon MO (St Louis area)
Posts: 25
Default

Well done. I hope mine runs that good this year.
Bryan
__________________
Bryan


87 GN with 43k
Stock block Champion GN1 14 bolt, ARP bolts, Cottons valve covers, Comp Cams 218/212 hyd roller, Scorpion rockers, Comp Cams double roller, home ported intake, Champion 1" plenum spacer, RJC PowerPlate, Turbonetics GT-K 850 BB, 3" DP with external wastegate, Cottons 4" cold air kit, Cottons FMIC, 72# inj, FAST XFI, ALKYCONTROL, Hooker cat back, Art Carr 9" NLU, Art Carr internals,Precision turbo saver, Metco adjustable uppers, Metco lowers, HR sway bar, MT DRs
Reply With Quote
  #4  
Old 01-18-2008, 03:17 AM
PaceCarTA's Avatar
PaceCarTA PaceCarTA is offline
Da Big Cheese
 
Join Date: Dec 2007
Location: central NJ
Posts: 50
Default

thanks guys
its pretty well dialed in and brackets competitively at 10.7 with a slightly lowered running boost of 23psi and slightly lowered launch boost to about 7-8 psi so i can have my target boost before the green light , usually .040 or better, and to keep the risk of breaking tires loose with a 1.52- 1.55 60'
only thing i wish i had dialed in was the entry for this summers pinks at my hometown track , will be there spectating , showing support and if need be to lend a hand to my fellow buick club members who made the list
__________________
Paul... NJ rep MAGNABUICK.com
the 86 3450lbs ...1.44 6.19@112 9.72@138 ,
109 234cu stock mains and bolts , irons,
the 87 ttop ,1.37 6.0@ 114 9.45 @ 141.9 25 psi !!
109 235cu .gn1 alum, certified roll cage .
the 87gnx'd FAST B2B TA49 ..back to all stock original #s 109 and trans hipro w stagerite
the 87 GN ttop ..all stock with vac brakes
86 WH1 mini tubbed roll caged 109, extreme 2004r
all on pump 93 and alkycontrol
Reply With Quote
  #5  
Old 01-18-2008, 05:24 PM
JCotton1's Avatar
JCotton1 JCotton1 is offline
Married Man
 
Join Date: Nov 2007
Location: Paradise
Posts: 1,434
Default

that's good stuff Paul.....
__________________
Jack Cotton
Cottons Performance
413-789-0531
Reply With Quote
  #6  
Old 01-19-2008, 12:21 AM
jhuber jhuber is offline
In way too deep!!
 
Join Date: Dec 2007
Posts: 32
Default

Pauly (aka The Good Doctor) IS The Man!!!
He's been there for all my best times and has helped me run a TA49 way passed Normal times!!!
__________________
John Huber

Mid-Atlantic Grand National Association (MAGNA)
Club Director & New Jersey State Rep.

#2 rocks to the tune of 12.25@107mph, Stock turbo
#2 rocks to the tune of 10.98@121mph, TA49 turbo
Reply With Quote
  #7  
Old 01-19-2008, 12:28 AM
PaceCarTA's Avatar
PaceCarTA PaceCarTA is offline
Da Big Cheese
 
Join Date: Dec 2007
Location: central NJ
Posts: 50
Default

hey john!!

heres the link to a cool GN video , your 12second run on the stocker is in it as well as a couple of my 10.4 passes that day

http://videos.streetfire.net/video/e...8c013e4547.htm
__________________
Paul... NJ rep MAGNABUICK.com
the 86 3450lbs ...1.44 6.19@112 9.72@138 ,
109 234cu stock mains and bolts , irons,
the 87 ttop ,1.37 6.0@ 114 9.45 @ 141.9 25 psi !!
109 235cu .gn1 alum, certified roll cage .
the 87gnx'd FAST B2B TA49 ..back to all stock original #s 109 and trans hipro w stagerite
the 87 GN ttop ..all stock with vac brakes
86 WH1 mini tubbed roll caged 109, extreme 2004r
all on pump 93 and alkycontrol

Last edited by PaceCarTA; 01-19-2008 at 01:18 AM.
Reply With Quote
  #8  
Old 01-19-2008, 01:02 AM
jhuber jhuber is offline
In way too deep!!
 
Join Date: Dec 2007
Posts: 32
Default

That was a great day, Pauly!!!

Me beating Don...Nice
The 12.27 run against Artie...Real nice!!!
You smacking the balz off the Mustang....Priceless
__________________
John Huber

Mid-Atlantic Grand National Association (MAGNA)
Club Director & New Jersey State Rep.

#2 rocks to the tune of 12.25@107mph, Stock turbo
#2 rocks to the tune of 10.98@121mph, TA49 turbo
Reply With Quote
  #9  
Old 01-20-2008, 02:56 PM
scot w.'s Avatar
scot w. scot w. is offline
28lbs on pump gas! :)
 
Join Date: Jan 2008
Location: Smokey Mtns, in TN
Posts: 34
Thumbs up

Nice times Paul, congrats!
__________________
1986 GN, 235cu. Bal & blueprinted 109 block, PT-70 gtq, Billit mains on 2&3, ARP main studs, J&E pistons/dry film coated w/ ceramic tops, Dry-Film coated bearings(rods,main,cam), M&A stage III alum heads-race ported-wire locked w/ARP studs, ATR headers, Hyd. flat tappet 221/218-525lift/cam, crower 1.65 roller rockers, race ported intake, 70mm Acufab TB, percision plenum,3"THDP, 85lb inj flow matched, P.T.E S/L IC, Razors ALKY kit, 9" 3800 N-stall N/L art-carr conv, Moser axles, H&R bar
Reply With Quote
  #10  
Old 07-08-2009, 06:07 PM
twinrats twinrats is offline
Junior Member
 
Join Date: Apr 2009
Posts: 2
Default Great Tome on a stock bottom end

WOW! 10's on a stock bottom end! Good Luck...you're going to need it. I hope it stays together for you.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:17 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.