|
|
|||||||
| Transmissions and Torque Converters Tranny and torque converter tech support |
 |
|
|
Thread Tools | Display Modes |
|
#1
11-08-2010, 11:29 PM
|
||||
|
||||
Choosing a torque converter...
Now that I've made up my mind and have decided to follow Jack's recommandation, I'll be going with a TH-400 next year.
 I've been doing a little researching on the net for a torque converter and I found a lot of manufacturers... There's PTC, ATI, TCI, JW, Art Carr, Precision, Hughes, Neil Chance, Coan, to name a few... I know my good friend Martin has tried both PTC and ATI back-to-back and seems to have had better results with the ATI. I, myself have always had some Art Carr converters in my GN, but that is with the 200-4R. I looked at his website and he seems to be more specialized in 200-4R's than TH-400's...  For some reason, I seem to have confidence into the ATI, but do not trust PTC... I think I'll choose a "spragless" type from ATI...What do you think? links: http://www.atiracing.com/products/tc/tc.htm Claude. 
__________________
1987 Buick Grand National 9.70 e.t. @ 139.35 mph 1971 Chevelle SS 2008 Ford F-350 Crew Cab Dually 2012 Lincoln MKX Last edited by toofastforyou; 11-16-2010 at 09:13 PM. 
|
|
#2
11-11-2010, 09:07 PM
|
||||
|
||||
?...anyone?...
 Claude.
__________________
1987 Buick Grand National 9.70 e.t. @ 139.35 mph 1971 Chevelle SS 2008 Ford F-350 Crew Cab Dually 2012 Lincoln MKX
|
|
#3
11-12-2010, 02:40 PM
|
||||
|
||||
|
Welcome to the 400 side Claude.. You have made a good decisioin. I don't have a lot of track time with my 400, but I can tell you that the ATI fuel/blown convertor MPH's very well. This was the convertor Jack recommended for me. On another note, I'm thinking of purchasing 15x10 Street Lites to use with my 295 MT's. How do your 10's fit your car and what tires are you using on the street? Sorry, I don't remember. It's been a while since I've seen you. Brian
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car! Last edited by BrianHynes; 11-12-2010 at 02:42 PM.
|
|
#4
11-12-2010, 09:13 PM
|
||||
|
||||
|
Quote:
About my 15"x10" Street Lites, mine have a 4.5" rear spacing and fit ok with some P275-60-15 tires and NO frame notch. They're close to the frame inside (about 1/2"), but absolutely no rubbing. Below are some pictures (viewed under the car in front of the rear tires) showing the clearance between the frame and tire's sidewall bulge...Hope this helps! One last note...I use a 1/4" spacer on the left side to have the same clearance on both sides (as the rear axle is rarely perfectly centered under the car... )Take care, regards, Claude. 
__________________
1987 Buick Grand National 9.70 e.t. @ 139.35 mph 1971 Chevelle SS 2008 Ford F-350 Crew Cab Dually 2012 Lincoln MKX Last edited by toofastforyou; 11-12-2010 at 09:17 PM.
|
|
#5
11-16-2010, 01:26 PM
|
||||
|
||||
|
Hey Claude...
You know where I stand, either ATI or PTC will work fine. They both work. Sometimes they need to be restalled to get what we are looking for, bottom line, both work well at your level.... There is no magic converter, even though there are those out there that want you to believe that...
__________________
Jack Cotton Cottons Performance 413-789-0531
|
|
#6
11-16-2010, 08:58 PM
|
||||
|
||||
|
Quote:
And last, I'll pass on the "magic converters" ...  Thank you, talk to you soon... Claude.
__________________
1987 Buick Grand National 9.70 e.t. @ 139.35 mph 1971 Chevelle SS 2008 Ford F-350 Crew Cab Dually 2012 Lincoln MKX Last edited by toofastforyou; 11-16-2010 at 09:00 PM.
|
|
| Bookmarks |
|
|
Linear Mode
