|
|
|||||||
| Ask Jack The best place to find me for any reason |
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
08-30-2008, 07:21 PM
|
||||
|
||||
was looking in your store page
Hey jack,i wasnt able to find in your store page if you sell VDO COCKPIT OIL PRESSURE GAUGES.
I SUPPORT MY BUICK VENDERS ONLY,AND YOU ARE THE 1'ST ON THE LIST  AS YOU HEARD IM HAVING ISSUES WITH THE GN. ? LOOKING FOR CAM,VALVE SPRINGS AND DOUBLE TIMING CHAIN BUT WOULD PREFER 1 STEP BETTER THAN STOCK, VERY MILD SETUP
__________________
210/210 DLS roller cam kit,2 1/2 hookers exhaust,test pipe,t49 turbo @ 20psi,42LB,billet adj fuel regulator,adj waste gate, tt chip,160 thermostat,hot wire kit,torque strap,boost&vac gauge,knock gauge,,billet aluminum vacuum block,17'' budnik wheels,Scanmaster,LT1 MAF,Translator,Vigilante 9 1/2 torque converter 2800 TO 3200 stall,trans cooler,Jimmy's rebuild trans,walbro fuel pump,PTE stock location ic,37,000plus miles and maybe alky to be a little slower Last edited by DA87GN; 08-30-2008 at 07:34 PM. 
|
|
#2
08-30-2008, 08:03 PM
|
||||
|
||||
|
Jack will be in e-town for the weekend, so it might be Monday before you get a response. Is there a reason for wanting VDO?
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
|
|
#3
08-30-2008, 09:56 PM
|
||||
|
||||
|
all other gauges are VDO
__________________
210/210 DLS roller cam kit,2 1/2 hookers exhaust,test pipe,t49 turbo @ 20psi,42LB,billet adj fuel regulator,adj waste gate, tt chip,160 thermostat,hot wire kit,torque strap,boost&vac gauge,knock gauge,,billet aluminum vacuum block,17'' budnik wheels,Scanmaster,LT1 MAF,Translator,Vigilante 9 1/2 torque converter 2800 TO 3200 stall,trans cooler,Jimmy's rebuild trans,walbro fuel pump,PTE stock location ic,37,000plus miles and maybe alky to be a little slower
|
|
#4
09-02-2008, 10:30 AM
|
||||
|
||||
|
Quote:
There are lots of parts we don't list, if you don't see it check with me, most likely we have or can get it. As for the VDO gauges, we do carry Autometer, but if needed, I should be able to get VDO. I have everything else you are looking for. Thanks for giving us the first shot...
__________________
Jack Cotton Cottons Performance 413-789-0531
|
|
#5
09-04-2008, 12:10 AM
|
||||
|
||||
|
hey JACK,I order the breather by-pass kit from you.im hoping by installing this kit will solve one of my problems with the turbo or if it is a turbo issue or not.
turbo,wastegate,wye hose,pvc valve and wastegate solenoid is all new, less than 300 miles on it. AND as far as the engine issue, i will be working on it some time in December.I HAVE A FUNNING FEELING THAT IT MAY BE A ISSUE WITH MY CAM/TIMING CHAIN GOING BAD
__________________
210/210 DLS roller cam kit,2 1/2 hookers exhaust,test pipe,t49 turbo @ 20psi,42LB,billet adj fuel regulator,adj waste gate, tt chip,160 thermostat,hot wire kit,torque strap,boost&vac gauge,knock gauge,,billet aluminum vacuum block,17'' budnik wheels,Scanmaster,LT1 MAF,Translator,Vigilante 9 1/2 torque converter 2800 TO 3200 stall,trans cooler,Jimmy's rebuild trans,walbro fuel pump,PTE stock location ic,37,000plus miles and maybe alky to be a little slower Last edited by DA87GN; 09-04-2008 at 12:12 AM.
|
|
| Bookmarks |
|
|
Hybrid Mode
