|
|
|||||||
| Suspensions, Street and Strip This is where we talk about new and different suspension packages and what works best for your type of driving |
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
03-19-2008, 03:51 PM
|
||||
|
||||
60' footing under 1.40
Anyone 60' footing under 1.40? What's your combo? Are you using the HR bar, Wolfe bar, coil overs, four link, tire size?
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143! 
|
|
#2
03-19-2008, 05:43 PM
|
||||
|
||||
Ca' mon Jack. Do tell!
__________________
'86 Gn with an RPE bullet. Almost everything else is from Cottons. 100% street car!
|
|
#3
03-19-2008, 05:53 PM
|
||||
|
||||
|
My best 60 foot was 1.47, I have South side machine bar lowers, Edlebrock adjustable uppers and an HR bar with 28 M/T's slicks on a 10 inch rim. I am pretty sure my pinion angle is at -3.5 degrees from what I can remember. As far as the rear goes, 3.42's with 33 spline axles,and spool.
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143!
|
|
#4
03-19-2008, 07:01 PM
|
||||
|
||||
|
My best is a 1.51. I think my problem was that I ran M/T 28x10.5's on a 10" rim, and I needed 15 psi in both air bags to insure the tires would not hit the fender lip. This totaly took suspension movement out of the equation. I have installed QA1's all around, fully adjustable lowers/uppers from Wolfe, -3 pinion angle, 3.42 w/ a US/Strange carrier, T/A Perf. cover, and Moser axles w/ Mark Williams C-clip elim.
|
|
#5
03-19-2008, 09:29 PM
|
||||
|
||||
|
Quote:
__________________
Jack Cotton Cottons Performance 413-789-0531
|
|
#6
03-20-2008, 12:19 AM
|
||||
|
||||
|
Quote:
__________________
87 GN, RPE built 109 stroked, RJC girdle, billet main caps, custom comp roller cam, Champion ported aluminum heads, Champion aluminum intake, T&D 1.65 rockers, 96 lb injectors, Accufab 70mm throttle body RJC pullies, RJC A/C bracket,GTK-850, ATR headers,Deeds electronic boost controller, Cotton’s 4 inch down pipe w/ Turbonetics RG 45 gate, XFI, Cotton’s front mount, Level 10 built 400 trans w/brake, Converter? ,33 spline Moser axles, Spool, HR bar. New best 9.44 @ 143!
|
|
#7
03-30-2008, 01:37 PM
|
||||
|
||||
|
not sub 1.4 but 1.41's
t-brake launches at 10psi (electronic boost controller) stock springs stock uppers stock lower (bottoms boxed) stock bushings MT drag radials (#23psi) and HR parts sway bar the trans, driveshaft and rear are built for low 60s 2004r , 9"art carr 14930, chromoly shaft , spicer yokes and ujoints moser 33 spline , moser spool , c-clip elems i probably could cut 1.3xs by dialing boost up a little and toss on some slicks , but with just a stock bottom end i cant be too hard on it. i run a stageright t-brake which engages by placing trans in 1st gear and releases by bumping out of 1st , because of this the shifter is in 2nd when you leave the line and 1-2 shift is auto trans controlled occurring early (5150) and within the first 60' (actually 42') , if i could carry 1st gear to 5850 the 60 should drop ...working on that as we speak 
__________________
Paul... NJ rep MAGNABUICK.com the 86 3450lbs ...1.44 6.19@112 9.72@138 , 109 234cu stock mains and bolts , irons, the 87 ttop ,1.37 6.0@ 114 9.45 @ 141.9 25 psi !! 109 235cu .gn1 alum, certified roll cage . the 87gnx'd FAST B2B TA49 ..back to all stock original #s 109 and trans hipro w stagerite the 87 GN ttop ..all stock with vac brakes 86 WH1 mini tubbed roll caged 109, extreme 2004r all on pump 93 and alkycontrol Last edited by PaceCarTA; 03-30-2008 at 02:03 PM.
|
|
| Bookmarks |
|
|
Hybrid Mode
