TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS  

Go Back   TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS > Search Forums

Showing results 1 to 16 of 16
Search took 0.00 seconds.
Search: Posts Made By: Razor
Forum: Alky / Meth Injection 11-13-2009, 06:58 PM
Replies: 1
Views: 12,577
Posted By Razor
New for 11/2009 failsafe for alky

In beta form right now, will be available before Christmas.

Needs a minimum 50 PSI air source or CO2 to operate. Cars that have CO2 for boost controllers can use this setup. We have a 10 OZ air...
Forum: Alky / Meth Injection 11-13-2009, 06:47 PM
Replies: 1
Views: 4,415
Posted By Razor
Transducer kit pixs :)

Transducer kit pixs :)
Forum: Alky / Meth Injection 11-13-2009, 06:43 PM
Replies: 1
Views: 4,415
Posted By Razor
XFI transducer datalogs

Twin nozzle setup. Look at the alky track boost ;)
Forum: Alky / Meth Injection 10-31-2009, 01:30 AM
Replies: 1
Views: 4,125
Posted By Razor
Plugs into the 3 bar for power.. orange wire is...

Plugs into the 3 bar for power.. orange wire is run into car tie into XFI input.

150 PSI Stainless Steel. can also be used for fuel or oil.

Contact Cottons for more info.

Cheers
Forum: Alky / Meth Injection 10-31-2009, 01:24 AM
Replies: 1
Views: 4,125
Posted By Razor
New stuff Nov 09

Pressure transducer kit for alcohol system. I'll post up pixs shortly on the harness.

Ties into the XFI input and you can record alky pressure. Works with the Power Logger and the FAST Dash as...
Forum: Ask Jack 02-02-2009, 05:53 PM
Replies: 2
Views: 2,229
Posted By Razor
This is the basic way to test the system. 1)...

This is the basic way to test the system.

1) Start engine
2) Place blue gain knob on position 8
3) Press and hold the test button until the engine stumbles/changes idle

The Power Injection...
Forum: Alky / Meth Injection 12-08-2008, 02:33 AM
Replies: 7
Views: 6,188
Posted By Razor
Absolutely.. the only way to make a kit. ...

Absolutely.. the only way to make a kit.

Contact Cottons for the deal ;)
Forum: Alky / Meth Injection 09-03-2008, 03:50 PM
Replies: 5
Views: 5,106
Posted By Razor
Recently I used this sucker to blow Hurricane...

Recently I used this sucker to blow Hurricane Faye away from the Tampa Bay area :D

Specs.. 572 BBC, twin 67's, FAST, 8 gallon SS alky tank ;)

0-60 specs.. hehe
Forum: Alky / Meth Injection 09-03-2008, 03:48 PM
Replies: 5
Views: 5,106
Posted By Razor
Fishing

Anyone want to go gator hunting? :eek:
Forum: Alky / Meth Injection 09-03-2008, 03:44 PM
Replies: 2
Views: 5,039
Posted By Razor
Tank.. put foam in the tank to keep the sloshing...

Tank.. put foam in the tank to keep the sloshing in check. ;)
Forum: Alky / Meth Injection 09-03-2008, 03:43 PM
Replies: 2
Views: 5,039
Posted By Razor
Race application

Here's a simple kit to combat high intake air temps. Motor is a SBC with a pair of 67's. Using a FM intake temps were at 170 degree's through the traps. With the alky kit, temps came down to 80...
Forum: Alky / Meth Injection 08-28-2008, 09:40 PM
Replies: 4
Views: 6,125
Posted By Razor
Yes and no. See the pump is capable of 200 PSI....

Yes and no. See the pump is capable of 200 PSI. Meaning if you set the system becuase you needed 200 PSI then that capability would be there.

Yes its regulated down, most operate at approx 30 PSI...
Forum: Alky / Meth Injection 08-27-2008, 05:46 PM
Replies: 4
Views: 6,125
Posted By Razor
Doing what your doing, your not adding any fuel....

Doing what your doing, your not adding any fuel. And I doubt you can get any really "real" gain due to the pressure output of the pump you run. The $500 dollar alky kits pump will make over 200 PSI...
Forum: Alky / Meth Injection 02-07-2008, 01:56 PM
Replies: 2
Views: 5,396
Posted By Razor
Two reasons. See if you knock at 15 PSI.....

Two reasons.

See if you knock at 15 PSI.. and you activate the system at 15 PSI.. you will knock until the alcohol hits the combustion chamber.. think of it as ping ping ping... then clean. So by...
Forum: Alky / Meth Injection 12-18-2007, 01:28 PM
Replies: 8
Views: 7,564
Posted By Razor
well two issues. One is the pump has a diaphram...

well two issues. One is the pump has a diaphram made of a material called "Santoprene" The other choice is a material called "Geolast". Both of these materials are not rated for petroleum. As a...
Forum: Alky / Meth Injection 12-11-2007, 04:21 PM
Replies: 8
Views: 7,564
Posted By Razor
The issue is the petroleum content in the E85....

The issue is the petroleum content in the E85. The systems are designed around chemicals not petroleums. Issue one is the reservoir.. then the pump..

Hope this helps.
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT. The time now is 04:24 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.