TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS

TEAM COTTON'S PERFORMANCE TURBO BUICK ONLINE FORUMS (http://community.cottonsperformance.viper05.citasystems.net/forum/index.php)
-   Buick Turbo Tech (http://community.cottonsperformance.viper05.citasystems.net/forum/forumdisplay.php?f=3)
-   -   help on next upgrade or tuning for more power (http://community.cottonsperformance.viper05.citasystems.net/forum/showthread.php?t=1909)

stevek 01-10-2011 05:25 PM

help on next upgrade or tuning for more power
 
Hellow I just joined this fourm, I'm wondering were to go next for making more power either in upgrades or tuning, here is a list of some thing I've put on my 86 gn,car runs good best time 12.00 @113, dyno@ 350 hp and 365 tk,60 series turbo,40 lb injectors,kenne bell 70 mm throttle body and upper intake, kenne bell high flow intank pump and kenne bell inline series 230l/b fuel pump, atr 3 in downpipe, kenne bell headers, ram air kiit, 100 lb valve springs,translater plus with extender chip,front mount intercooler from atr,SMC progressive alky system ,scan master and a/f meter guage. I'm running 24# boost,50 # fuel press at idle with hose off.scanmaster reads usually 770 to 820 and a/f reads 11.3 with alky on. if alky off sometimes 3-4 retard on scanmaster.just seeing were to go to make more power without to much money, any help would be appriciated, thanks

Night Train 01-10-2011 08:54 PM

If that is on pump gas with the alky, seems a little slow. I might opt for larger injectors. Are you running Methanol or Alcohol? I run meth on my setup. Perhaps Jack can help. Where are you located?

waGoN 01-10-2011 11:12 PM

I'm not familiar with that chip, but your fuel pressure seems a little high.
As for upgrades, I would say injectors and a turbo.
Although, you didn't say anything about tires/suspension.

stevek 01-11-2011 01:26 AM

Im located just outside charlotte nc, in huntersville nc. running straight methonal in system,rear tires are bfg drag radials with 2 air bags and larger sway bar with stronger control arms to axle.running on pump gas 93 octane

120k on 6 axles 01-16-2011 09:01 PM

I would go a ported stock TB vs the larger 70mm. a more injector & a little more turbo. just remember bigger is not always better. I went high 10.90's several years ago with a stock unopen motor, valve springs, TA 61 turbo, 55# inj. Pete Tomka cold air kit on VP c16 race gas @ 28psi & that was 99* heat @ Darlington.

why does it show I only have 1 post? is it because I have not posted in a long time?

stevek 01-18-2011 08:43 AM

thanks, I think i'm going to get larger injectors, and get a new chip ,do you know what is the largest injectors you can use with stock ecu ? and were to get new chip burned? the turbo i bought on ebay 2 years ago , how do i measure it to find out for sure what size it is ? I'll probably keep the 70 mm. tb on it looks good on top of motor. the time and speed i put up eailier, i just remembered it was with a ta49 turbo and no posi. I put posi in and 60 turbo ?and haven't gone back to the track yet just on dyno. any more help is great thank again

Night Train 01-18-2011 03:14 PM

Turbo Tweak has the best chips currently. You could get it through Jack Cotton and he could advise you on where to spend your money. It all depends on what your desired outcome is in terms of speed/ET and how much money you want to spend...:D

stevek 01-19-2011 04:51 PM

thanks I'll send message to jack see what he says, have a great day


All times are GMT. The time now is 05:53 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.